江苏龙网

  1. 首页 > 生活 > >

底盘|汽车研发与制造专业术语汇总( 三 )


reverse 倒车档
RFQ Request For Quotation询价
RKD Reverse Knock Down
RLQ Receiving Lot Quantity
ROC Rate of Climb
ROI return on investment 报酬率
ROP Re-Order Point
RTO Required To Operate
SAIS Supplier Assessment & Improvement System
SC Strategic Confirmation/significant Charac'teristics
SDS- System/ Design Specifications 系统/设计说明
second gear 二档
SFMEA System FMEA
Shipping Date 出货日、Invoice Date 发票日或On Board Date 装船日
Side Windshield 侧窗玻璃
SJ Strategic Intent
SNP Standard Number of Parts
SOW- state of work 工作申明
SPC Statistical Process Control
SQA Supplier Quality Assurance
SREA- Supplier Request for Engineering Approval 供应商工程设计更改申请
ST Surface Tranfer
STRS Supplier Test Report System
Subcontractor 分承包商
Sunroof Windshield 天窗玻璃
SUV Sports Utility Vehicle
TAG Test Aptitude Graphique
TCO Total Cost of Ownership 总持有成本
TCRA Total Cost Reduction Activity
TGR Things Gone Right
TGW Things Gone Worst
TM Techinical Manual
TPM Total Preventive Maintenance
TTO-Tool Try Out 工装验证
UOM Unit Of Measure
VES Vehicle Evaluation System
VO- Vehicle Operation 主机厂
VPP- Vehicle Program Plan 整车项目计划
VQA Vehicle Quality Assurance
VTTO- Vendor Tool Try-Out 供应商工装验证
WERS- World Wide Engineering Release System
WVTA Whole Vehicle Type Approval
凹坑 concave
车床 lathe
抽查试验spot check test
出厂试验delivery test
次品defective product
调幅amplitude modulation (AM)
调频 Frequency Modulation
断差 offset
对讲机 interphone
法平面normal plane
翻车rollover
返工 re-doing
防滑地板 no-skid floor
仿真emulation
副作用side effect
改装厂 refitting factory
隔热板heat shield
后围侧板 rear wall side cover
划痕 scratch
假人dummy
间隙 interstice
节点pitch point
结皮现象skinning
扭矩torque
汽车总布置草图sketch for automobile layout
汽车总装配图automobile assembly drawing
汽油供给管gasoline feed pipe
汽油箱gasoline tank( petrol tank)
前围角板 front wall angle cover
轻型客车light bus
曲轴crankshaft
三类底盘 three type chassis
上模upper die
甚高频very high frequency (VHF)
下模bottom die(counter die)
消声器silencer
选料上乘、做工精细be superior in material and excelllent in workmanship
仪表板 dash board
油门throttle
褶皱 crimple
整车运输transportation of truck-load
总装 final assembly
阻流板step,reflectro,baffle
最大扭矩转速speed at maximum torque
左对齐left justify
报废scrapping
皮纹 grain
OTS OFF TOOL SAMPLE 用批量生产的工模器具制造出的样件
PVS Produktions Versuchs Serie 批量试生产


推荐阅读


上一篇：汽车|途锐新添插电混动车型，添加科技配置

下一篇：奥迪|奥迪Q5L Sportback最新消息，将于广州车展上市